Bathroom Repairs in Aurora

Four repair calls we handle across Aurora

Not every call we receive in Aurora starts with picking out new porcelain slabs. Many start when a homeowner notices a yellowish ring spreading across the main-floor ceiling, feels a loose tile give way beside the toilet, or discovers that a recently renovated shower was tiled straight over bare drywall. Across Aurora’s older streets and 1990s subdivisions, four repair issues come up week after week:

1. Brown water rings or active drips on the main-floor ceiling directly below a second-floor ensuite or family bathroom.
2. Tiled showers that seep into baseboards, hold puddles on the floor, or shed loose tiles, often within two or three years of a cut-corner remodel.
3. Peeling bathroom paint, dark mildew along ceiling corners, and damp attic insulation caused by weak or unvented exhaust fans in 1960s–1990s houses.
4. Stalled or defective bathroom renovations left behind by a previous contractor, where the homeowner wants an honest assessment of what can stay and what has to be rebuilt.

Running a fresh bead of silicone over cracked grout or rolling stain-blocking primer over a damp ceiling never stops a plumbing or waterproofing failure—the repair has to happen where the water is escaping.

Tracing a water stain on the ceiling below an upstairs bathroom

When a water spot appears on your kitchen, hallway or family-room ceiling beneath an upstairs bathroom in Bayview Northeast, Aurora Highlands, Aurora Grove or Hills of St. Andrew, the water almost always comes from one of four sources:

• A failed wax ring or cracked flange under the toilet, or a dried-out gasket on a bathtub waste-and-overflow assembly.
• A hair-line crack in an acrylic shower pan or a tiled shower floor built without a continuous waterproof membrane.
• Open grout joints or failed silicone along a low shower niche, bench seam or mixing valve trim plate.
• A weeping copper solder joint, worn valve cartridge or pinhole supply leak inside the plumbing wall, which continues to drip even when no one is running the shower.

Rather than guessing, we isolate the source step by step. First we check whether the damp spot expands when the fixtures are turned off (which points to a pressurized water line) or only when someone uses the shower or drains the tub. Next we test the drain trap by itself before wetting the shower walls. Where the plumbing sits above a finished drywall ceiling, cutting a neat inspection opening from below lets us look straight at the subfloor and trap without breaking intact bathroom tile. Once the fault is confirmed, we quote both the bathroom fix and the ceiling repair in writing.

Rebuilding failed or poorly pitched tiled showers

When a tiled walk-in shower starts soaking the adjacent drywall or hallway carpet a couple of years after installation, regrouting the surface will not cure it. Opening the shower base almost always exposes the same shortcuts: ceramic tile mortared directly onto bare drywall, a flat pan with no pre-slope toward the drain, a wood curb wrapped in punctured plastic, or an unsealed shampoo niche.

Our crew strips the failed enclosure down to clean wood studs, dries and repairs any rotted framing or subfloor plywood, and rebuilds the shower with waterproof foam backer board, a properly sloped pan, and a continuous sheet membrane bonded to the drain flange—the exact system we use on all our walk-in showers in Aurora.

Fixing bathroom mould and attic-vented exhaust fans

In many 1960s, 1970s and 1980s homes across Regency Acres, Aurora Village, Aurora Heights and Aurora Highlands, the original builder exhaust fan either hums loudly without moving air or blows warm, humid air through an uninsulated hose straight into the attic insulation. During an Ontario winter, that steam condenses on cold roof sheathing and drips back down onto the ceiling drywall.

Replacing an aging fan with a quiet, properly sized unit and running an insulated duct to an exterior wall or roof hood is a standalone repair we perform across Aurora, and it stops recurring ceiling mildew for good. Where moisture has already softened drywall along a bathtub rim, we cut out the damaged board, treat the studs, and rebuild the surround with waterproof backer board.

Stepping in when another contractor leaves a job unfinished or leaking

Having to call a second company after a contractor walks off a job or builds a shower that leaks on week one is stressful. As Newmarket homeowner Lawrence noted in our client reviews, what matters most is a crew that fixes every issue pointed out and stays until the job is properly done.

We inspect the work in place, show you clearly which rough-ins or fixtures can be saved and what must be redone, and give you a line-by-line written quote. If the previous installer moved drains without a municipal permit, read our article on Aurora bathroom renovation permits and our checklist on how to vet a bathroom contractor in Aurora.

How bathroom repair work is priced in Aurora

Because repair scopes range from a two-hour valve and fan replacement to a complete shower pan rebuild, we quote repairs by the exact work needed. From our published Aurora bathroom renovation cost page, licensed plumbing and electrical trades are $70 to $120 per hour, and full room demolition and disposal is about $1,500. When extensive hidden water damage means the entire room is more economical to rebuild from the studs, we price the job from our published full bathroom renovation or tub-to-shower conversion packages starting at $8,000 in labour.

Upload a photo of the issue to get started

Take a clear photo of the ceiling stain, loose tile or unfinished room—along with a wider shot of the bathroom—and send them through our free quote form or contact page. If water is actively dripping right now, close the fixture shut-off valve (or your main house water shut-off) and call us at (647) 800-6880. Every repair we complete is backed by our written labour warranty.